3-POS Remote Installation
WARNING: Always wear safety glasses and protective gloves during service to prevent potential injury. Failure to wear protective equipment during service may lead to SERIOUS INJURY OR DEATH.
FIT4 3-POS PTL REMOTE INSTALL
![img/help/page2920-DXA3/IMG_8422 copy2-m.jpg](img/help/page2920-DXA3/IMG_8422 copy2-m.jpg)
Step 1
Install the remote lever under bar on the rider's left side. Tighten the clamp screw clockwise to 15in-lb (1.7Nm)
![img/help/page2920-DXA3/IMG_8424 copy-m.jpg](img/help/page2920-DXA3/IMG_8424 copy-m.jpg)
Step 2
Install a short piece of housing with one ferrule. Fully seat the housing in the remote lever
![img/help/page2920-DXA3/IMG_8427 copy-m.jpg](img/help/page2920-DXA3/IMG_8427 copy-m.jpg)
Step 3
Install the in-line barrel adjuster with it fully threaded together for maximum adjust range.
![img/help/page2920-DXA3/IMG_8435 copy-m.jpg](img/help/page2920-DXA3/IMG_8435 copy-m.jpg)
Step 6
With all the housing fully seated thread the cable through the remote housing and around the pulley.
![img/help/page2920-DXA3/IMG_8440 copy-m.jpg](img/help/page2920-DXA3/IMG_8440 copy-m.jpg)
Step 7
While holding the cable tight, tighten the pinch bolt with a 2mm Hex Wrench then cut off exccess cable and crimp the end.
3-POS PTL DUAL REMOTE INSTALL
![img/help/page2920-DXA3/IMG_8455 copy-m.jpg](img/help/page2920-DXA3/IMG_8455 copy-m.jpg)
Step 1
Install the remote lever under bar on the rider's left side. Tighten the clamp screw clockwise to 15in-lb (1.7Nm)
![img/help/page2920-DXA3/IMG_8463 copy-m.jpg](img/help/page2920-DXA3/IMG_8463 copy-m.jpg)
Step 3
Install the in-line barrel adjusters in their fully threaded together configuration for maximum range.
![img/help/page2920-DXA3/IMG_8435 copy2-m.jpg](img/help/page2920-DXA3/IMG_8435 copy2-m.jpg)
Step 6
With all the housing fully seated and no slack in the system, thread the cable through the remote housing and around the pulley
![img/help/page2920-DXA3/IMG_8440 copy2-m.jpg](img/help/page2920-DXA3/IMG_8440 copy2-m.jpg)
Step 7
While holding the cable tight, tighten the pinch bolt with a 2mm hex wrench, cut off excess cable and crimp the end.
![img/help/page2920-DXA3/IMG_8473 copy-m.jpg](img/help/page2920-DXA3/IMG_8473 copy-m.jpg)
Step 8
With all housing fully seated and no slack in the system, thread the second cable though the shock remote housing and around the pulley.
![img/help/page2920-DXA3/IMG_8478 copy-m.jpg](img/help/page2920-DXA3/IMG_8478 copy-m.jpg)
Step 9
While holding the cable tight, tighten the pinch bolt with a 2mm hex wrench. Do not turn the torx screw that attaches the remote pulley to the shock.
WARNING: FOX products should be installed by a qualified bicycle service technician, in accordance with FOX installation specifications. If you have any doubts as to whether or not you can properly install the remote lever on your bicycle, defer to a professionally trained bicycle service technician. Improperly installed products can fail, causing the rider to lose control, potentially causing SERIOUS INJURY OR DEATH.
WARNING: Make sure that the remote lever does not interfere with normal brake and shift lever operation. Failure to do so can result in loss of control, potentially causing SERIOUS INJURY OR DEATH.
WARNING: Make sure to leave enough cable housing length to accomodate normal steering operation. Failure to do so can result in loss of control, potentially causing SERIOUS INJURY OR DEATH.